Copyright © GSE ONLINE SDN BHD ( 1116968-P ) ALL RIGHTS RESERVED
H) Order procedures
1) Cash & Carry ( ex-factory )

OR

2) Formal PO issuance :-
Step 1 ) , Issue PO and e-mail to ( sales@gserubber.com ) .
( follow quotation number above in your PO , Leadtime : Within 1 ~ 7 working days )
​( * subject to GSe stock level )

Step 2 ) Contact / e-mail GSE Sales office for proforma invoice and payment arrangement in advance before collection .


​​​​​​​​A) Product Name
100% homogeneous Vulcanised EPDM RUBBER SPEED BUMP with locks to prevent dislocation after installation .
​( With Cat Eyes Reflective Glass )


B) Brand  
RUDSAF ™  ( ROADSAFE ) ,

MADE IN MALAYSIA

​​C) Raw Material 

Made of 100% homogeneous Vulcanised EPDM Rubber
​( No Recycled / Reclaimed Rubber ) & molded with around 3mm of EPDM Yellow wear layer for Yellow Part for better visibility . 


​​D) Purpose
1) Control vehicle speeds to promote pedestrian safety
2) Reduce the risk of accidents in parking areas and residential streets

​​E) Scope

Speed bumps are more aggressive traffic calming options and are useful in places where pedestrians and cars share space closely, like parking lots and driveways.

​​F) Characteristics
Our RUDSAF meets Australian/New Zealand Standards of “AS/NZS2890.1:2004 Parking Facilities” , it determines four main types of criteria for speed Bumps.

Why AS/NZS2890.1:2004 Parking Facilities ?
AS/NZS2890.1:2004 is an Australian/New Zealand Standard that provides guidance for specific minimum requirements for the design and layout of off-street car parking.

​​The content within AS/NZS2890.1:2004 can be quite comprehensive as our reference.


​​Bumps that comply with standards are determined by height, cross section, markings and ramps angles explained below.


Criteria 1 )
Height : Must be between 25 to 75mm.

​​
Criteria 2 )
Cross Section : Must be flat on top of around 100mm ~ 150mm and Shape cannot in parabolic or peaked.

​​
Criteria 3 )
Ramp Angle : Must have a ramp angle 2:1

​​
Criteria 4 )
Markings : Must have alternating yellow stripes 250mm wide.

RUDSAF EPDM RUBBER SPEED BUMPS

Why We Choose Homogeneous EPDM Rubber & What are the Benefits of using EPDM Rubber ?

i) Homogeneous EPDM Rubber will compress under high impact better than recycled/ reclaimed rubber.

ii) Resistance to UV exposure, ozone, aging, weathering and many chemicals - great for outdoor applications , Do not use EPDM rubber if continual contact with petroleum-based products is required.

iii) Stability in high and low temperatures - EPDM material can be used in severe environment condition and the withstand temperature range from -20⁰F to +300⁰F (-29⁰C to 150⁰C)

iv) Low electrical conductivity

​v) Steam and water resistant


vi) Properties allow it to be widely used and highly​versatile, can be applied successfully in many situations

​vii) Used in the proper environment, the parts will work well and last long without breaking down, becoming brittle, etc.


​​
G) SPECIFICATION
1) Manufacture from High Density 100% Homogeneous EPDM Rubber with cat’s eye and “ LOCK “ features to prevent dislocation after installation, an additional advantage for uneven / soft Asphalt ( Tar ) road surface.

​2) Available in Black & Yellow combination for greater visibility


​3) Anti skid surface with flat top of 110mm Width as defined under
AS/NZS2890.1:2004 Parking Facilities of Criteria 2.

​4) All units can purchase separately


​5) Sizes :-

​i) Model : RSBB250X310, 100% BLACK EPDM Rubber, Middle Black Speed Bumps with Lock,~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc

ii) Model : RSBY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, Middle Yellow Speed Bumps with Lock, ~50mm Thickness, ~310mm Width x ~250mm Length/pc, ~3.3kgs/pc

iii) Model : RECB250X310, 100% BLACK EPDM Rubber, End Cap Black Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc

iv ) Model : RECY250X310, 100% EPDM Rubber with ~3mm Yellow Top Wear Layer, End Cap Yellow Speed Bumps,~50mm Thickness, ~310mm Width x ~250mm Length/pc with slope, ~2.5kgs/pc

​​ RECOMMENDED Lag bolts :- 

​​ A) For concrete , use ½ inch diameter lag bolts and 4 to 5-inch in length


​​​​​​​

​Disclaimer :
​* Note : Users need to evaluate suitability for their industries use ( applications ) before placing order from us .

HIGH QUALITY

​RUDSAF 
​100% EPDM RUBBER
​ ​SPEED BUMP

RUBBER SPEED HUMP



 
 
 
 
 
 
GSE TRADEMARK rudsaf speed bump Malaysia 25mm 100mm h2h speed hump yellow stripe Malaysia
Criteria 1 )
Criteria 2 )
Criteria 3 )
Criteria 4 )
AS/NZS2890.1:2004
Roadsafe Traffic Yellow End Cap Malaysia Roadsafe speed hump Black Middle Black Malaysia Roadsafe speed hump Middle Yellow Malaysia Roadsafe Traffic Black End Cap Malaysia
Advantages :-

​(1) DIS-LOCATION PREVENTION
Speed bump dislocation Malaysia Speed bump after assembling Speed bump before assembling
BEFORE ASSEMBLING
AFTER ASSEMBLING
ROADSAFE MIDDLE BLACK SPEED BUMP MALAYSIA
ROADSAFE MIDDLE YELLOW SPEED HUMP MALAYSIA
ROADSAFE END CAP MALAYSIA
ROADSAFE END CAP YELLOW
ROADSAFE MIDDLE SPEED BUMP FULL MALAYSIA
ROADSAFE END CAP MARK MALAYSIA
ROADSAFE END CAP LOGO MALAYSIA
ROADSAFE END CAP END CAP TRADEMARK MALAYSIA
ROADSAFE END CAP TRADEMARK MALAYSIA
ROADSAFE AUTHENTIC END CAP MALAYSIA
High Quality 100% EPDM Rubber Speed Hump Quotation Malaysia
Lag Bolts & Installation Excluded